More about the Edition of Parameters

Here is a list of all the commands whose parameters can be modified in the 3D area when creating or editing a feature.

Related Topics
Displaying and Modifying the Dimensions of a Feature Directly


  • This capability is available with the following Generative Shape Design commands:

Command Type Sub- Type Parameter(s) displayed
Bump    
Deformation Distance (Maximum distance along the deformation direction from the deformed surface)
Circle Center and Radius   Radius, Start Angle, End Angle
Center and Point   Start Angle, End Angle
Two Points and Radius   Radius
Bitangent and Radius   Radius
Curve as center element   Radius
Corner Radius
Curve Parallel Geodesic parallel mode Constant (Offset Distance)
Diabolo Draft Angle
Extrapolate Length Length, Limit Type
Extrude Length 1, Limit 1 Length 2, Limit 2
Helix Taper Angle, Starting Angle Pitch Height
Line Angle/Normal to Curve Support and Geometry on support selected Length (Start and End) Infinite Start Point: End Infinite End Point: Start Infinite: /
Point-Point Support selected
Point-Direction Support selected
Tangent to Curve Mono-tangent and Support selected
Normal to Surface  
Bisecting Support selected
Offset     Offset Value
Plane Angle/Normal to Plane   Angle
Offset from Plane   Length, Offset Distance
Point Coordinates   Length, X, Y, Z coordinates
On Curve Geodesic Length (distance on curve)
On Plane   Length, H, V
On Surface   Length (distance on surface)
Polyline     Radius, Radius at point
Reflect Line     Angle
Revolve     Angle1, Angle2
Rotate     Rotation Angle
Shape Fillet Bi-Tangent Fillet   Radius
Sphere     Parallel Start Angle, Parallel End Angle, Meridian Start Angle, Meridian End Angle
Radius
Spiral Angle and Radius   Start Radius End Radius End Angle
Angle and Pitch   Start Radius Pitch End Angle
Radius and Pitch   Start Radius End Radius Pitch
Sweep Explicit Sweep    
Linear Sweep Two Limits Angle
    With Reference Surface
Length1, Length2
 
With Reference Curve Angle, Length1, Length2
    With Draft Direction
Angle, Length1, Length2
Translate   Distance and Direction Distance
 


  • This capability is available with the following Part Design commands:

    Note: For Chamfer, Chordal Fillet and Face-Face Fillet, there is no manipulator and therefore no linked ruler. For Circular Pattern and Draft, the manipulation arrow appears if the angle is positive and less than 180 degrees.

Command Parameter(s) or manipulator(s) displayed
Chamfer Angle, Length1, Length2
Chordal Fillet n Length
Circular Pattern Angle, Length
Draft constant Angle
Draft reflect Angle
Draft variable n Angle
Edge Fillet Radius, n Setback
Face-Face Fillet Radius
Groove Angle1, Angle2, Thickness1, Thickness2, LIM1, LIM2
Hole (simple) Diameter, Depth, Bottom
  Counterbored Diameter1, Depth1, Diameter2, Depth2, Bottom
  Counterdrilled Diameter1, Depth1, Angle, Depth2, Diameter2, Bottom
  Countersunk Diameter1, Depth1, Angle, Diameter2, Depth2
  Tapered Diameter1, Depth1, Angle, Bottom
Multipad n LIM1, n LIM2
MultiPocket n LIM1, n LIM2
Pad Length1, Length2, Thickness1, Thickness2, LIM1, LIM2
Pocket Length1, Length2, Thickness1, Thickness2, LIM1, LIM2
Rectangular Pattern Length1, Length2
Rib Thickness1, Thickness2
Shaft Angle1, Angle2, Thickness1, Thickness2, LIM1, LIM2
Shell n Length1, n Length2
Stiffener Thickness1, Thickness2
Slot Thickness1, Thickness2
Thickness n Length1, n Length2
Thick Surface Length1, Length2
Thread Diameter, Depth
Variable Fillet n Radius, n Setback